Call Us: +1 866 300 9012

contact@measur.ca
SHOPPING CART

No Products in the Cart

TOTAL:
$0.00
Radiodetection SuperCAT4

    Radiodetection SuperCAT4

    $1,810.00
    The SuperCAT4+ range of locators and transmitters uses a selection of passive, sonde and active frequencies designed to target specific buried assets. Using Radiodetection’s familiar C.A.T controls and display, minimal retraining is required to access these advanced capabilities.

    SuperCAT4+ can be used to locate a comprehensive set of active frequencies to support the detection and tracing of different cable types in varied environmental conditions. Higher frequencies such as the 131kHz or 65kHz can be used to find well-insulated utilities such as twisted-pair telecom cables or insulated pipe joints. For long range locating of lower resistance cables, such as power lines, lower frequency options are available.

    Cable Avoidance Tools


    Warranty
    Weather Rating
     Battery 
    Start-up Time

    2 years

    IP54

    D-Cell

    Instant



    The SuperCAT4+ range of locators and transmitters uses a selection of passive, sonde and active frequencies designed to target specific buried assets. Using Radiodetection’s familiar C.A.T controls and display, minimal retraining is required to access these advanced capabilities.

    For oil and gas pipes using a Cathodic Protection System, the CPS model can locate the rectified signal without needing an additional transmitter.

    The S model locates a range of sonde frequencies that can be matched to the challenges of finding water and drain pipes. A lower frequency sonde is useful to trace deep cast-iron pipes. Higher frequency sondes can be easier to distinguish in an electronically noisy urban environment.

    SuperCAT4+ can be used to locate a comprehensive set of active frequencies to support the detection and tracing of different cable types in varied environmental conditions.  Higher frequencies such as the 131kHz or 65kHz can be used to find well-insulated utilities such as twisted-pair telecom cables or insulated pipe joints.  For long range locating of lower resistance cables, such as power lines, lower frequency options are available.




    Safety Built-In

    All SuperCAT4+ models come with a range of features designed to aid safe working practices.

     

    Dynamic Overload Protection

    High levels of electrical interference, as found around substations and near high-voltage transmission cables can overload sensitive electronics. Dynamic Overload Protection filters this interference out, enabling SuperCAT4+ to continue locating where other units struggle.

     

    Dig more safely with StrikeAlert™

    StrikeAlert  warns the user to the possible presence of shallow cables and utility lines in both Power and Active Line modes.

    Although work practices and guidelines insist power cables are buried below a certain depth, a common cause of cable strikes is unexpectedly shallow cables.

     

    TRUDEPTH™

    Indicates depth when the locator is oriented correctly above the target cable, pipe or sonde for the most accurate reading.

     

    Real Sound

    The audio signals emitted by the SuperCAT4+ are derived from the signals detected. Radio, Power and Active signals can be easily distinguished from each other, and from background noise, helping identification of target utilities, and aiding differentiation of closely co-located utilities. 


    Locate Pipelines Protected by a Cathodic Protection System

    SuperCAT4+CPS and T1-512/T1-640

    Optimized for metal pipes that use rectified currents as part of their Cathodic Protection System. The CPS signal can be located and traced without the need to apply an additional transmitter signal to the pipeline.

     

     


    Find Water and Drain Pipes

    SuperCAT4+S and T1-512/T1-640

    For the challenge of detecting and tracing buried pipes, the SuperCAT4+S locates the widest range of sonde frequencies. Additionally, an active 33kHz frequency can be applied to a FlexiTrace using a T1-512 or 640 for continuous signal tracing.

     

     


    Detect a Broad Range of Utilities

    SuperCAT4+

    Designed to meet the demanding environments of the construction industry, this multi-utility locator can be used with a wide range of sondes and accessories.

    Pair with the higher frequency range of T1-131 for environments where locating Telecom or high-impedance cables are a priority. Alternatively, use with the 65/512/640 for a lower frequency range suitable for pipe tracing.

     


    BACK TO TOP